EPW2GFS - ACI
Automation Field Components
Pulse Width Modulation Input (2.93 sec), Pressure Output (0-15PSI), Dual Valve, Exhausts on Power Failure, Gauge, Version 1, (10, 5, 25 sec), (0-10PSI, 0-20PSI)
This item is temporarily out of stock.
It can be backordered right now, and we can ship it within 5 weeks.
0
106333
ACI
U.S.A.
{{CMP.TITLE}}
- Features
- Comments (0)
-
Data Sheet
EPW2GFS - ACI
Automation Field Components
download pdfPlease contact us if you need any other document this item may have.
You can only download Technical Document (Datasheet) on this section.
The EPW* converts a pulse, phase cut, or digital PWM signal into a proportional pneumatic signal ranging from 0 to 20 psig. The pneumatic output is proportional to the signal input, either direct or reverse acting. The EPW* has a manual override potentiometer to vary the pneumatic output and two LEDs, one to indicate power and one for signal status. The EPW* offers four jumper selectable input timing ranges. Output pressure ranges are jumper shunt selectable for 0 to 10, 0 to 15 and 0 to 20 psig, and adjustable in all ranges. A 0-5 VDC feedback signal indicating the resultant branch line pressure, is also provided. This signal varies linearly with the branch pressure range selected. EPW* is designed with electrical terminals on one end and pneumatic connections on the other, allowing for maximum convenience in wiring and tubing installation when panel mounted. Three basic configurations are available: The EPW is a constant bleed interface with branch exhaust response time determined by the bleed orifice size and pressure differentials. If power fails to the EPW, it will continue to bleed through the bleed orifice until branch pressure is zero psig. The EPW2 incorporates two valves (one controls exhaust) and does not bleed air at set point. Its branch exhaust flow and response time are not limited by an internal restrictor and are similar to its load rate. If power fails to the EPW2, branch line pressure remains constant if the branch line does not leak air. FAIL SAFE: The EPW2FS is a two valve fail safe model. Its 3-way branch exhaust valve allowsm exhaust of branch line air on a power failure.,All factory calibrated products are NIST traceable. Certificates of Compliance must be ordered with product. EU Commission Directive 2002/95/EC (RoHS) Compliant.
- Three way mixing valve control
- Pilot positioner control
- Compressor staging
Warranty :This product is under warranty for 2 years against manufacturing and material defects from the date of invoice. The invoice for the products also stands in place of the warranty certificate, a separate document is not issued.Delivery Information :ACI branded products are imported from United States of America factory specially to order. The estimated delivery time of the products is 5 weeks. In this product group, an additional shipping and customs fee of 450EUR is charged for orders under 4,000EUR.
A/TT1K-LT-I-6'-4-BB - ACI
Automation Field Components
Transmitter w/ 1,000 Ohm RTD, Low Temperature Immersion, Welded Well, 6' 316SS, NEMA 3R Enclosure, 4-20mA
A/1/4' COMPRESSION FITTING - ACI
Automation Field Components
1/4' Compression Fitting
A/20K-PO-6' - ACI
Automation Field Components
20,000 Ohm Thermistor, Probe Only, 6'
85930-018-098 - ACI
Automation Field Components
Smart Sensor Replacement, Silane, 0-50 ppm
A/TUC2-CP-0105 - ACI
Automation Field Components
10,000 Ohm Thermistor (Type II), Setpoint, w/ Override, LCD
A/TUCH2-CP-0013 - ACI
Automation Field Components
LCD, RH3%, SET, O/R, DEG F
A/TT100-R2-4 - ACI
Automation Field Components
Transmitter w/ 100 Ohm RTD, Room (R2), 4-20mA Output